This page compares flake, metallic, and solid colour floors so the differences are clear. The floors Final Finish installs are flake. We use Torginol products.

The quick comparison

  • Flake is the practical choice for most garages. A base coat, a broadcast of coloured flake, a scrape, and a clear top coat make a textured, speckled floor that hides dust, grit, and small scratches.
  • Solid colour is one even colour under a top coat. It looks clean and architectural and brightens a room, but it shows dust, tire marks, and scratches sooner.
  • Metallic is poured and worked by hand so metallic pigments settle into swirls and depth. No two floors are alike. It is the most decorative of the three and the least forgiving of dust and wear.

All three are epoxy systems on prepared concrete. The preparation underneath follows the same idea for each, because the prepared surface has to suit the coating, as the ICRI guideline on surface preparation sets out. What changes is what you see, and how the floor lives with daily use.

How each one looks

Flake reads as texture from across the room and as colour up close. The colour comes from the blend, a mix of tones and chip sizes. Full coverage, where flake covers the whole base, gives a granite-like surface. Partial coverage lets the base colour show between the chips. Our flake colour guide covers how blends read in different light.

Solid colour is calm. Greys, charcoals, and light neutrals are common in garages and workshops. A light solid floor bounces light around and makes a room feel bigger.

Metallic floors have movement. Light travels through the pigments, so the floor looks different at noon and at night. That depth is the appeal, and the variation is part of it: the final pattern is shaped by the pour and cannot be predicted exactly. Read the metallic expectations guide before choosing one.

What each one hides, and what it shows

This is where most people decide.

  • Dust and grit. Flake hides them best. Solid and metallic floors show a film of dust sooner, especially in dark colours.
  • Scratches. Every coated floor scratches under grit and dragged equipment. Flake disguises fine scratches in its pattern. Solid and metallic floors show them in raking light.
  • Tire marks. Hot tires can mark any coating, and the marks are easiest to see on light solid colours. The hot-tire pickup guide explains the causes.
  • Salt rings. Edmonton winters bring meltwater and road salt into garages. The white rings it leaves when it dries show on dark solid and metallic floors. A mid-tone flake blend hides them.

Grip underfoot

A smooth, glossy floor can be slippery when wet, whatever its colour. Flake adds a little texture on its own. For any of the three, an anti-slip top coat adds grip where people walk in wet boots or where water sits.

The CCOHS guidance on preventing slips, trips, and falls is written for workplaces, and it names the quality of the walking surface as a key factor. The same holds in a garage or a mudroom. Our slip resistance guide goes into texture and top coats.

Which finish suits which room

These notes compare the three approaches. The floors Final Finish installs are flake. A finer flake blend is the calm option where a metallic or solid colour floor is sometimes discussed.

  • Garage. Flake handles grit, salt, and daily parking, and still looks good between cleanings.
  • Basement living space. A finer flake blend reads calmer where the floor is seen more. See the basement guide.
  • Workshop. A light flake blend brightens the room and still hides marks. Grip where oil or water is around.
  • Showroom or commercial space. A flake floor can stay quiet or carry more contrast. The solid-colour commercial guide explains the even-colour alternative. Final Finish’s commercial floors are flake.
  • Mudroom. Flake with grip, because boots and water arrive together.

Time on the floor, and what it means for the quote

The preparation underneath is the same idea for all three, so the differences come from the layers on top.

  • Flake has a rhythm: base coat, broadcast, scrape, top coat. The broadcast is fast, and the scrape and top coat make the surface even.
  • Solid colour goes down in rolled or squeegeed coats. It is the simplest to install, and the least forgiving of a poorly prepared slab, because every flaw in the concrete shows through an even colour.
  • Metallic is poured and worked by hand while it is wet, so it takes the most skilled time on the floor. The look depends on that hand work, which is why two metallic floors never match.

Those differences show up in time and in the quote. Ask for the options side by side so you compare like with like; the guide to garage coating costs explains the other factors.

Colour and light in an Edmonton garage

Garage light changes the colour you chose. Winter daylight is low and blue, and most garage lighting is cool LED. Warm greys can look flat under cool light, and very dark floors swallow light in a single-bulb garage. Before choosing, look at colours in your own space at the time of day you use it most. A light or mid-tone floor makes a garage brighter to work in, and hides salt rings better than black.

Living with each one

All three clean the same way: a dust mop or soft broom, then a damp mop with a mild cleaner. The difference is how often you notice the need. Flake forgives a busy week. Solid and metallic floors look their best with more frequent dust mopping. The cleaning guide has the details.

See it before you choose

Colour on a screen is a starting point. The finish library shows the flake colours Final Finish installs, and the floor visualizer puts a flake blend on a photo of your own space. When you have a direction, ask Denis about a flake floor. See residential flake floors and garage flake floors.

Questions people ask

Which epoxy finish is best for a garage in Edmonton?
For most garages, flake. Its texture and speckled colour hide grit, salt residue, and fine scratches between cleanings, and it gives a little grip underfoot. Solid colour and metallic floors suit rooms that see less winter traffic.
Is a metallic epoxy floor slippery?
A smooth, glossy metallic floor can be slippery when wet, like any glossy surface. Where water or snow comes in, an anti-slip top coat adds grip. In dry living spaces, most people keep the smooth finish.
Do scratches show on a solid colour epoxy floor?
More than on flake. Every coated floor scratches under grit and dragged equipment, but a flake pattern disguises fine scratches, while a solid colour shows them in low, raking light. Dust mopping and felt pads help.
Can I see the finishes on my own floor before choosing?
The floor visualizer lets you try flake colours on a photo of your own space. Colour on a screen is a starting point, so talk through the blend with Denis before the quote.

Residential flake floors